Ubuntut használok.. és Lilo-t

és nem jelenik meg menü.. ha oprendszer menüre gondlsz.. Ja és bepostoltam.. hozzáférés megtagadva

partició kiosztás: cat /proc/partitions vagy cat /etc/fstab
lilo.conf megmutatása:
su :kéri a rendszergazdai jelszót
cat /etc/lilo.conf
Ha ezt megadod, akkor pár perc alatt olyan állat lilo.conf-ot összehozunk neked… 😀

# /etc/lilo.conf – See: `lilo(8)’ and `lilo.conf(5)’,
#

---

      `install-mbr(8)’, `/usr/share/doc/lilo/’,
#                      and `/usr/share/doc/mbr/’.

# +

---

+
# |                        !! Reminder !!                        |
# |                                                              |
# | Don’t forget to run `lilo’ after you make changes to this    |
# | conffile, `/boot/bootmess.txt’ (if you have created it), or  |
# | install a new kernel.  The computer will most likely fail to  |
# | boot if a kernel-image post-install script or you don’t      |
# | remember to run `lilo’.                                      |
# |                                                              |
# +

---

+

# Specifies the boot device.  This is where Lilo installs its boot
# block.  It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda

# Specifies the device that should be mounted as root. (`/’)
#
root=/dev/hda1

# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller.  Using `compact’ is especially recommended when
# booting from a floppy disk.  It is disabled here by default
# because it doesn’t always work.
#
# compact

# Installs the specified file as the new boot sector
# You have the choice between: text, bmp, and menu
# Look in lilo.conf(5) manpage for details
#
#install=menu

# Specifies the location of the map file
#
map=/boot/map

# You can set a password here, and uncomment the `restricted’ lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration.  If a
# command line is given, other than one specified by an `append’
# statement in `lilo.conf’, the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh’,
# and thus becoming `root’ without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr’ to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well.  Please RTFM `install-mbr(8)’.
#
# password=tatercounter2000

# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=20

# You can put a customized boot message up if you like.  If you use
# `prompt’, and this computer may need to reboot unattended, you
# must specify a `timeout’, or it will sit there forever waiting
# for a keypress.  `single-key’ goes with the `alias’ lines in the
# `image’ configurations below.  eg: You can press `1′ to boot
# `Linux’, `2′ to boot `LinuxOLD’, if you uncomment the `alias’.
#
# message=/boot/bootmess.txt
#      prompt
#      delay=100
#      timeout=100

# Specifies the VGA text mode at boot time. (normal, extended, ask, )
#
# vga=ask
# vga=9
#
vga=normal

# Kernel command line options that apply to all installed images go
# here.  See: The `boot-prompt-HOWTO’ and `kernel-parameters.txt’ in
# the Linux kernel `Documentation’ directory.
#
# append=””

# If you used a serial console to install Ubuntu, this option should be
# enabled by default.
# serial=

#
# Boot up Linux by default.
#
default=Linux

image=/vmlinuz
        label=Linux
        read-only
#      restricted
#      alias=1

        initrd=/initrd.img

image=/vmlinuz.old
        label=LinuxOLD
        read-only
        optional
#      restricted
#      alias=2

        initrd=/initrd.img.old

# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other’ line to
# where your other OS’ partition is.
#
# other=/dev/hda4
#      label=HURD
#      restricted
#      alias=3

hát hallod nemtudom ti hogyan tanultatok meg ennyi mindent.. de majd egyszer talán én is oszthatom az észt.. :blush: