vasy ~ # dmesg
virtual kernel memory layout:
    fixmap  : 0xffe16000 – 0xfffff000  (1956 kB)
    pkmap  : 0xff800000 – 0xffc00000  (4096 kB)
    vmalloc : 0xf8800000 – 0xff7fe000  ( 111 MB)
    lowmem  : 0xc0000000 – 0xf8000000  ( 896 MB)
.init : 0xc0553000 – 0xc0598000  ( 276 kB)
.data : 0xc0408ec2 – 0xc054bf10  (1292 kB)
.text : 0xc0100000 – 0xc0408ec2  (3107 kB)
Checking if this processor honours the WP bit even in supervisor mode… Ok.
Calibrating delay using timer specific routine.. 4814.54 BogoMIPS (lpj=9629095)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400
00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00003080 00004400 0000000
0 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Compat vDSO mapped to ffffe000.
Checking ‘hlt’ instruction… OK.
Freeing SMP alternatives: 18k freed
ACPI: Core revision 20070126
Parsing all Control Methods:
Table [DSDT](id 0001) – 556 Objects with 53 Devices 160 Methods 31 Regions
tbxface-0587 [02] tb_load_namespace : ACPI Tables successfully acquired
evxfevnt-0091 [02] enable : Transition to ACPI mode successful
CPU0: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
Booting processor 1/1 eip 2000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4811.24 BogoMIPS (lpj=9622490)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400
00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00003080 00004400 0000000
0 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 09
Total of 2 processors activated (9625.79 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
migration_cost=37
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfbc20, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
evgpeblk-0952 [04] ev_create_gpe_block  : GPE 00 to 1F [_GPE] 4 regs on int 0x9
evgpeblk-1049 [03] ev_initialize_gpe_bloc: Found 8 Wake, Enabled 1 Runtime GPEs
in this block
Completing Region/Field/Buffer/Package initialization:……………………..
………………………………………
Initialized 31/31 Regions 9/9 Fields 19/19 Buffers 12/17 Packages (565 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:..
Executed 2 _INI methods requiring 1 _STA executions (examined 58 objects)
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH4 GPIO
Boot video device is 0000:01:00.0
PCI: Transparent bridge – 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: Power Resource [PFAN] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
SCSI subsystem initialized
libata version 2.20 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn’t work, try „pci=routeirq”.  If it helps, post a report
pnp: 00:0b: ioport range 0x400-0x4bf could not be reserved
pnp: 00:0d: iomem range 0xcd000-0xcffff has been reserved
pnp: 00:0d: iomem range 0xf0000-0xf7fff could not be reserved
pnp: 00:0d: iomem range 0xf8000-0xfbfff could not be reserved
pnp: 00:0d: iomem range 0xfc000-0xfffff could not be reserved
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 17 (level, low) -> IRQ 16
Time: tsc clocksource has been installed.
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16]  MMIO=[fb005000-fb0057ff]  Max
Packet=[2048]  IR/IT contexts=[4/8]
PCI: Bridge: 0000:00:01.0
  IO window: 9000-9fff
  MEM window: f8000000-f9ffffff
  PREFETCH window: e8000000-f7ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: a000-afff
  MEM window: fa000000-fbffffff
  PREFETCH window: 50000000-500fffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Machine check exception polling timer started.
IA-32 Microcode Update Driver: v1.14a
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Real Time Clock Driver v1.12ac
intel_rng: FWH not detected
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 sec
onds).
Hangcheck: Using get_cycles().
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
ACPI: Transitioning device [FAN] to D3
ACPI: Transitioning device [FAN] to D3
ACPI: Fan [FAN] (off)
ACPI: Invalid passive threshold
ACPI: Thermal Zone [THRM] (49 C)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver – version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 18 (level, low) -> IRQ 17
eth0: RealTek RTL8139 at 0xf881e000, 00:50:8d:f5:aa:c8, IRQ 17
eth0:  Identified 8139 chip type ‘RTL-8101’
netconsole: not configured, aborting
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 17
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0…
Probing IDE interface ide1…
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00508d0000f4aac8]
hdc: DVD RW DVR-MCC, ATAPI CD/DVD-ROM drive
hdd: SAMSUNG SP1604N, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide0…
hdd: max request size: 512KiB
hdd: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63, UDMA(100)
hdd: cache flushes supported
hdd: hdd1 hdd2 hdd3
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
3ware Storage Controller device driver for Linux v1.26.02.002.
ata_piix 0000:00:1f.2: version 2.10ac1
ata_piix 0000:00:1f.2: MAP [ P0 — P1 — ]
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x0001c000 ctl 0x0001c402 bmdma 0x0001d000 irq 17
ata2: SATA max UDMA/133 cmd 0x0001c800 ctl 0x0001cc02 bmdma 0x0001d008 irq 17
scsi0 : ata_piix
ATA: abnormal status 0x7F on port 0x0001c007
scsi1 : ata_piix
ata2.00: ATA-7: Maxtor 6Y080M0, YAR511W0, max UDMA/133
ata2.00: 156312576 sectors, multi 16: LBA
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA Maxtor 6Y080M0  YAR5 PQ: 0 ANSI: 5
sd 1:0:0:0: [sda] 156312576 512-byte hardware sectors (80032 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn’t support DPO
or FUA
sd 1:0:0:0: [sda] 156312576 512-byte hardware sectors (80032 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn’t support DPO
or FUA
sda: sda1 sda2 sda3
sd 1:0:0:0: [sda] Attached SCSI disk
sd 1:0:0:0: Attached scsi generic sg0 type 0
Fusion MPT base driver 3.04.04
Copyright (c) 1999-2007 LSI Logic Corporation
Fusion MPT SPI Host driver 3.04.04
ieee1394: raw1394: /dev/raw1394 device initialized
usbmon: debugfs is not available
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 18, io mem 0xfc000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2006 August 04 USB 1.1 ‘Open’ Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000bc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000b000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 17, io base 0x0000b400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-8: new high speed USB device using ehci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000b800
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 1-8: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver…
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input2
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
Intel 810 + AC97 Audio, version 1.01, 21:49:59 Jul 31 2007
oprofile: using NMI interrupt.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Using IPI Shortcut mode
input: ImExPS/2 Generic Explorer Mouse as /class/input/input3
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 276k freed
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel 865 Chipset.
agpgart: AGP aperture is 128M @ 0xe0000000
ACPI: PCI Interrupt 0000:02:07.0[A] -> GSI 23 (level, low) -> IRQ 18
EXT3 FS on sda3, internal journal
Adding 506036k swap on /dev/sda2.  Priority:-1 extents:1 across:506036k
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
fglrx: module license ‘Proprietary. (C) 2002 – ATI Technologies, Starnberg, GERM
ANY’ taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 927 MBytes.
[fglrx] module loaded – fglrx 8.33.6 [Jan  8 2007] on minor 0
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 19
[fglrx] Internal AGP support requested, but kernel AGP support active.
[fglrx] Have to use kernel AGP support to avoid conflicts.
[fglrx] AGP detected, AgpState  = 0x1f004a1b (hardware caps of chipset)
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[fglrx] AGP enabled,  AgpCommand = 0x1f004312 (selected caps)
[fglrx] total GART = 134217728
[fglrx] free   GART = 118222848
[fglrx] max single GART = 118222848
[fglrx] total LFB  = 134217728
[fglrx] free   LFB  = 116387840
[fglrx] max single LFB  = 116387840
[fglrx] total Inv  = 0
[fglrx] free   Inv  = 0
[fglrx] max single Inv  = 0
[fglrx] total TIM  = 0
eth0: no IPv6 routers present
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on hdd3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
usb 1-8: USB disconnect, address 2
usb 5-2: new full speed USB device using uhci_hcd and address 2
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 3
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 4
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 5
usb 5-2: device not accepting address 5, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 7
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 8
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 9
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 10
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 11
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 13
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 14
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 15
usb 5-2: device not accepting address 15, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 16
usb 5-2: device not accepting address 16, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 17
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 18
usb 5-2: device descriptor read/64, error -71
usb 5-2: device descriptor read/64, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 19
usb 5-2: device not accepting address 19, error -71
usb 5-2: new full speed USB device using uhci_hcd and address 20
usb 5-2: device not accepting address 20, error -71
usb 1-8: new high speed USB device using ehci_hcd and address 11
usb 1-8: configuration #1 chosen from 1 choice
usb 1-8: USB disconnect, address 11
usb 1-8: new high speed USB device using ehci_hcd and address 12
usb 1-8: configuration #1 chosen from 1 choice
vasy ~ #