Alcatel USB Adsl modem hogyan?

Kezdőlap Fórumok UHU Linux Általános UHU problémák, javaslatok Alcatel USB Adsl modem hogyan?

9 bejegyzés megtekintése - 1-9 / 9
  • Szerző
    Bejegyzés
  • #1947259
    Joco8192
    Felhasználó

      A 2.6.5 kernelben van Driver hozzá csak figyelni kell a be konfigolásnál.

      #1947260
      admin
      Adminisztrátor
        #1947261
        Joco8192
        Felhasználó

          ADSL ?

          #1947262
          admin
          Adminisztrátor

            Szval egy Alcatel Speed Touch USB ADSL modemrõl lenne szó.

            A leírások, amik alapján csináltam:
            http://linux-usb.sourceforge.net/SpeedTouc…docs/howto.html
            http://cvs.sourceforge.net/viewcvs.py/*che…n.html?rev=HEAD

            Kezdtem a 2.6.5-ös kernel fordításával ezeket bejelöltem:

            Code Maturity Level Options —>
            Prompt for development and/or incomplete code/drivers

            Loadable Module Support —>
            Enable Loadable Module Support

            General Setup —>
            Support for hot-pluggable devices

            Networking Options —>
            Packet Socket
            Asynchronous Transfer Mode (ATM) (EXPERIMENTAL)
            RFC 1483/2684 Bridged protocols

            Network Device Support —>
            PPP (Point-to-Point Protocol) Support
            PPP Deflate Compression
            PPP support for sync tty ports
            PPP Over ATM (EXPERIMENTAL)
            PPP Over Ethernet (EXPERIMENTAL)

            USB Support —>
            Support for USB
            Preliminary USB Device Filesystem
            UHCI (Intel PIIX4, VIA,…) Support
            OHCI (Compaq, iMacs, OPTi, SiS, ALi, …) support
            UHCI Alternate Driver (JE)
            EHCI ….

            Character devices —>

            [*] Non-standard serial port support
            HDLC line discipline support

            [*]Unix98 PTY support

            Felraktam a speedtouch-1.2.tar.gz-t (modem driver)

            #1947263
            Joco8192
            Felhasználó
              ” wrote:
              Szval egy Alcatel Speed Touch USB ADSL modemrõl lenne szó.

              A leírások, amik alapján csináltam:
              http://linux-usb.sourceforge.net/SpeedTouc…docs/howto.html
              http://cvs.sourceforge.net/viewcvs.py/*che…n.html?rev=HEAD

              Kezdtem a 2.6.5-ös kernel fordításával ezeket bejelöltem:

              Code Maturity Level Options —>
              Prompt for development and/or incomplete code/drivers

              Loadable Module Support —>
              Enable Loadable Module Support

              General Setup —>
              Support for hot-pluggable devices

              Networking Options —>
              Packet Socket
              Asynchronous Transfer Mode (ATM) (EXPERIMENTAL)
              RFC 1483/2684 Bridged protocols

              Network Device Support —>
              PPP (Point-to-Point Protocol) Support
              PPP Deflate Compression
              PPP support for sync tty ports
              PPP Over ATM (EXPERIMENTAL)
              PPP Over Ethernet (EXPERIMENTAL)

              USB Support —>
              Support for USB
              Preliminary USB Device Filesystem
              UHCI (Intel PIIX4, VIA,…) Support
              OHCI (Compaq, iMacs, OPTi, SiS, ALi, …) support
              UHCI Alternate Driver (JE)
              EHCI ….

              Character devices —>

              [*] Non-standard serial port support
              HDLC line discipline support

              [*]Unix98 PTY support

              Felraktam a speedtouch-1.2.tar.gz-t (modem driver)

              #1947264
              Joco8192
              Felhasználó

                Szolgáltató neve ?

                #1947265
                admin
                Adminisztrátor

                  A szolgáltatóm Globonet :(((((((((.

                  Köszi a segítséget holnap kiróbálom.

                  #1947266
                  admin
                  Adminisztrátor

                    Még mindig nem müxik 🙁

                    A probélma az, hogy mint Usb eszközt felismer, de mint hálózati eszközt nem.

                    A winfos alatt vmi ilyesmi van:

                    Hálózati kártyák —]
                    3com …
                    SpeedTouch™ USB ADSL RFC1483

                    SpeedTouch USB Modem —]
                    SpeedTouch ADSL Modem (ISDN)

                    A kernelben találtam vmi RFC 15xx-t, de az nem RFC1483.

                    #1874456
                    csaba
                    Felhasználó

                      A fentebb említett modemmel a gond a következõ:
                      Letöltetöttem hozzá a drivert: SpeedTouch.tar.gz
                      Ebben azt írják, hogy:


                      You will need to install this kernel with the following options enabled:

                      – Code maturity level options / Prompt for development and/or incomplete code/drivers
                      – USB support / Support for USB
                      – USB support / Preliminary USB device filesystem
                      – Networking options / Asynchronous Transfer Mode (ATM) (EXPERIMENTAL)

                      The first option is necessary to be able to enable ATM.
                      When you upgrade your kernel, do not forget to upgrade your modutils!
                      (You will need version 2.4.2 or newer)
                      The modutils package can be found at:

                      http://www.kernel.org/pub/linux/utils/kern…/modutils/v2.4/

                      You will need SARLib-0.2.1 to compile this module.
                      You can download this library at:

                      http://sarlib.sourceforge.net/

                      Extract the SARLib in the same directory as this package.
                      Make sure your new 2.4.1+ kernel is in /usr/src/linux/
                      If it is not the case, you can also modify the path in the Makefile
                      Then type:

                      make

                      then become root and type:

                      make install

                      To be able to use this driver, you will have to install more than these two
                      packages. After installation of this package (and plugging in the modem) your system will feature an ATM device.



                      A probléma az, hogy nemtom mi az a modutils, a sarlib-et nem tudom felrakni, és a modem telepítõ + keresi a sarlibet.
                      Próbálkozott már vki hasonló modemmel?

                    9 bejegyzés megtekintése - 1-9 / 9
                    • Be kell jelentkezni a hozzászóláshoz.