smartmontools -szal mengézted már a vinyó(i)dat?

ez egy belsõ állapotellnõrzõ „rendszer” , lehet, hogy itt találsz okot, hogy miért romlott el a sector

linuxvilág májusi száma

javítás engem is érdekel.

Tud ebbõl vki kihámozni valamit?
Részleteibe kommentezve!
Elõre is köszönöm.

dark:~# smartctl -a /dev/hdc
smartctl version 5.30 Copyright © 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model: MAXTOR 4K040H2
Serial Number: 672132369028
Firmware Version: A08.1500
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 5
ATA Standard is: ATA/ATAPI-5 T13 1321D revision 1
Local Time is: Wed Jul 7 10:48:26 2004 CEST
SMART support is: Available – device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity was
never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 44) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 26) minutes.

SMART Attributes Data Structure revision number: 11
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x0029 100 253 020 Pre-fail Offline – 0
3 Spin_Up_Time 0x0027 086 084 020 Pre-fail Always – 1866
4 Start_Stop_Count 0x0032 097 097 008 Old_age Always – 2330
5 Reallocated_Sector_Ct 0x0033 100 100 020 Pre-fail Always – 0
7 Seek_Error_Rate 0x000b 100 100 023 Pre-fail Always – 0
9 Power_On_Hours 0x0012 094 094 001 Old_age Always – 4202
10 Spin_Retry_Count 0x0026 100 100 000 Old_age Always – 0
11 Calibration_Retry_Count 0x0013 100 100 020 Pre-fail Always – 0
12 Power_Cycle_Count 0x0032 098 098 008 Old_age Always – 1640
13 Read_Soft_Error_Rate 0x000b 100 100 023 Pre-fail Always – 0
194 Temperature_Celsius 0x0022 089 082 042 Old_age Always – 30
195 Hardware_ECC_Recovered 0x001a 017 003 000 Old_age Always – 510252892
196 Reallocated_Event_Count 0x0010 100 253 020 Old_age Offline – 0
197 Current_Pending_Sector 0x0032 100 100 020 Old_age Always – 0
198 Offline_Uncorrectable 0x0010 100 253 000 Old_age Offline – 0
199 UDMA_CRC_Error_Count 0x001a 163 163 000 Old_age Always – 37

SMART Error Log Version: 1
ATA Error Count: 142 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Timestamp = decimal seconds since the previous disk power-on.
Note: timestamp „wraps” after 2^32 msec = 49.710 days.

Error 142 occurred at disk power-on lifetime: 1515 hours
When the command that caused the error occurred, the device was in an unknown state.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
— — — — — — —
40 59 07 60 be 01 e0 Error: UNC 7 sectors at LBA = 0x0001be60 = 114272

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
— — — — — — — —

Error 141 occurred at disk power-on lifetime: 1515 hours
When the command that caused the error occurred, the device was in an unknown state.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
— — — — — — —
40 59 07 60 be 01 e0 Error: UNC 7 sectors at LBA = 0x0001be60 = 114272

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
— — — — — — — —

Error 140 occurred at disk power-on lifetime: 1515 hours
When the command that caused the error occurred, the device was in an unknown state.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
— — — — — — —
40 59 07 60 be 01 e0 Error: UNC 7 sectors at LBA = 0x0001be60 = 114272

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
— — — — — — — —

Error 139 occurred at disk power-on lifetime: 1515 hours
When the command that caused the error occurred, the device was in an unknown state.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
— — — — — — —
40 59 07 60 be 01 e0 Error: UNC 7 sectors at LBA = 0x0001be60 = 114272

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
— — — — — — — —

Error 138 occurred at disk power-on lifetime: 1515 hours
When the command that caused the error occurred, the device was in an unknown state.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
— — — — — — —
40 59 07 60 be 01 e0 Error: UNC 7 sectors at LBA = 0x0001be60 = 114272

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
— — — — — — — —

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

a nagy baj akkor van, ha  a reallocated sectors megindul, nálad udma CRC errorokat látok, ez lehet pl. kábel miatt (mint nálam, pont tegnap feküdt meg 120 GB filerendszer, szerencsére helyre tudtam állítani, ma megyek új kábelért)
viszont a Hardware ECC recovered elég csúnyán néz ki, csak most nem tudom mivel összevetni…
szóval próbáld meg a kábelcserét, és nézeges sûrûn a syslogot (dmesg), hogy van-e benne vinyóhiba (pl. seek error, stb) kábelcsere elõtt és után

na igen pont az ilyen figyelésre van a smartd démon, csak még én sem lõttem be

egyébként ha utána olvasol akkor kimondottan beszédes tud lenni a fenti üzenet…

ja, kimondotta a vinyókra
van belõle ubk-s csomi

ahogy néztem a smartd konfigját, még az én kezdetleges angoltudásommal sem vészes.
a linuxvilág cikkét meg tudom javasolni, ha hozzá tudsz férni

ha hozzá tudsz férni

Csak pénz kérdése…

le fog menni az ára, olyan 1700 forint köré, és nem lesz hozzá cd melléklet
a véleményem az, hogy semmi nincs abban az újságban ami nincs a neten, de itt viszont össze van szedve egy helyre. én ezért veszem, mert megmutatja hol az info, meg nem nagyon tudok angolul