# The BTTV module does not load the tuner module automatically,
# so do that in here
post-install bttv insmod tuner
post-remove bttv rmmod tuner

alias char-major-81 videodev
alias char-major-81-0 bttv
pre-install bttv modprobe -k tuner
options bttv radio=0 card=0
options bttv card=78 tuner=5

debian:~# dmesg
Linux version 2.4.27-2-386 (horms@tabatha.lab.ultramonkey.org) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 Wed Aug 17 09:33:35 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 – 000000000009f800 (usable)
BIOS-e820: 000000000009f800 – 00000000000a0000 (reserved)
BIOS-e820: 00000000000eb400 – 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 – 0000000011ff0000 (usable)
BIOS-e820: 0000000011ff0000 – 0000000011fffc00 (ACPI data)
BIOS-e820: 0000000011fffc00 – 0000000012000000 (ACPI NVS)
BIOS-e820: 00000000fffeb400 – 0000000100000000 (reserved)
287MB LOWMEM available.
On node 0 totalpages: 73712
zone(0): 4096 pages.
zone(1): 69616 pages.
zone(2): 0 pages.
ACPI disabled because your bios is from 00 and too old
You can enable it with acpi=force
Kernel command line: root=/dev/hda1 ro
Local APIC disabled by BIOS — reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 466.851 MHz processor.
Console: colour VGA+ 80×25
Calibrating delay loop… 930.61 BogoMIPS
Memory: 285668k/294848k available (1069k kernel code, 8792k reserved, 459k data, 96k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU:    After generic, caps: 0183fbff 00000000 00000000 00000000
CPU:            Common caps: 0183fbff 00000000 00000000 00000000
CPU: Intel Celeron (Mendocino) stepping 05
Enabling fast FPU save and restore… done.
Checking ‘hlt’ instruction… OK.
Checking for popad bug… OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer …
….. CPU clock speed is 466.8297 MHz.
….. host bus clock speed is 66.6899 MHz.
cpu: 0, clocks: 666899, slice: 333449
CPU0
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfd9d6, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router SIS5595 [1039/0008] at 00:01.0
PCI: Found IRQ 9 for device 00:00.1
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
COMX: driver version 0.85 (C) 1995-1999 ITConsult-Pro Co.
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 3692 blocks [1 disk] into ram disk… done.
Freeing initrd memory: 3692k freed
VFS: Mounted root (cramfs filesystem).
Freeing unused kernel memory: 96k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide: late registration of driver.
SIS5513: IDE controller at PCI slot 00:00.1
PCI: Found IRQ 9 for device 00:00.1
SIS5513: chipset revision 208
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS620 ATA 66 controller
    ide0: BM-DMA at 0xdcf0-0xdcf7, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xdcf8-0xdcff, BIOS settings: hdc:DMA, hdd:pio
hda: ST320014A, ATA DISK drive
blk: queue d2825b60, I/O limit 4095Mb (mask 0xffffffff)
hdc: PIONEER DVD-RW DVR-110D, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63, UDMA(33)
Partition check:
/dev/ide/host0/bus0/target0/lun0: [PTBL] [2434/255/63] p1 p2 < p5 >
Journalled Block Device driver loaded
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Adding Swap: 835340k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
Real Time Clock Driver v1.10f
hdc: attached ide-cdrom driver.
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Linux video capture interface: v1.00
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-algo-bit.o: i2c bit algorithm module
i2c-core.o: driver i2c TV tuner driver registered.
bttv: driver version 0.7.108 loaded
bttv: using 4 buffers with 2080k (8320k total) for capture
bttv: Bt8xx card found (0).
PCI: Found IRQ 9 for device 00:0b.0
PCI: Sharing IRQ 9 with 00:0b.1
bttv0: Bt878 (rev 17) at 00:0b.0, irq: 9, latency: 132, mmio: 0xfedfc000
bttv0: using: Jetway TV/Capture JW-TV878-FBK, Kworld KW-TV878RF [card=78,insmod option]
tuner: chip found @ 0xc0
i2c-core.o: client [(tuner unset)] registered to adapter [bt848 #0](pos. 0).
i2c-core.o: adapter bt848 #0 registered as adapter 0.
bttv0: using tuner=5
tuner: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
bttv0: i2c: checking for TDA9875 @ 0xb0… not found
bttv0: i2c: checking for TDA7432 @ 0x8a… not found
bttv0: PLL: 28636363 => 35468950 .. ok
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
SCSI subsystem driver Revision: 1.00
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 232M
agpgart: Detected SiS 620 chipset
agpgart: AGP aperture is 64M @ 0xf8000000
PCI: Found IRQ 3 for device 00:0a.0
3c59x: Donald Becker and others. http://www.scyld.com/network/vortex.html
See Documentation/networking/vortex.txt
00:0a.0: 3Com PCI 3c905B Cyclone 100baseTx at 0xdc00. Vers LK1.1.18-ac
00:01:02:19:30:e9, IRQ 3
  product code 434d rev 00.9 date 03-25-00
  Internal config register is 1800000, transceivers 0xa.
  8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface.
  MII transceiver found at address 24, status 7849.
  Enabling bus-master transmits and whole-frame receives.
00:0a.0: scatter/gather enabled. h/w checksums enabled
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
PCI: Found IRQ 10 for device 00:06.0
Crystal 4280/46xx + AC97 Audio, version 1.28.32, 09:49:41 Aug 17 2005
cs46xx: Card found at 0xfedfe000 and 0xfec00000, IRQ 10
cs46xx: Unknown card (1013:6003) at 0xfedfe000/0xfec00000, IRQ 10
ac97_codec: AC97 Audio codec, id: CRY3 (Cirrus Logic CS4297)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Found IRQ 11 for device 00:01.2
usb-ohci.c: USB OHCI at membase 0xd298d000, IRQ 11
usb-ohci.c: usb-00:01.2, Silicon Integrated Systems [SiS] USB 1.0 Controller
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
btaudio: driver version 0.7 loaded [digital+analog]
PCI: Found IRQ 9 for device 00:0b.1
PCI: Sharing IRQ 9 with 00:0b.0
btaudio: Bt878 (rev 17) at 00:0b.1, irq: 9, latency: 33, mmio: 0xfedfb000
btaudio: using card config „default”
btaudio: registered device dsp1 [digital]
btaudio: registered device dsp2 [analog]
btaudio: registered device mixer1
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x1001
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
tuner: TV freq (0.00) out of range (44-958)
debian:~#