Ja,akkor azért!

Ezt írja a dmesg:

Linux version 2.4.24-4 (uhubuild@ojjektum) (gcc version 3.3.2) #1 SMP Fri Jan 23 01:42:40 CET 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 – 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 – 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 – 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 – 000000000a000000 (usable)
BIOS-e820: 00000000ffff0000 – 0000000100000000 (reserved)
0MB HIGHMEM available.
160MB LOWMEM available.
ACPI: have wakeup address 0xc0002000
On node 0 totalpages: 40960
zone(0): 4096 pages
zone(1): 36864 pages
zone(2): 0 pages
ACPI disabled because your bios is from 97 and too old
You can enable it with acpi=force
Kernel command line: root=/dev/ide/host0/bus0/target0/lun0/part2
Local APIC disabled by BIOS — reenabling
Found and enabled local APIC
Initializing CPU#0
Detected 634.787 MHz processor.
Console: colour VGA+ 80×25
Calibrating delay loop… 1264.84 BogoMIPS
Memory: 153680k/163840k available (1426k kernel code, 9772k reserved, 1199k data , 152k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
Page cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
Enabling fast FPU save and restore… done.
Enabling unmasked SIMD FPU exception support… done.
Checking ‘hlt’ instruction… OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU0: Intel Celeron (Coppermine) stepping 03
per-CPU timeslice cutoff: 365.63 usecs.
task migration cache decay timeout: 10 msecs.
SMP motherboard not detected.
Enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
Calibrating APIC timer …
….. CPU clock speed is 634.8113 MHz
….. host bus clock speed is 66.8220 MHz
cpu: 0, clocks: 668220, slice: 334110
CPU0
migration_task 0 on cpu=0
ACPI: Subsystem revision 20031203
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfdb01, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0596] at 00:07.0
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards…
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
devfs: v1.12d (20021015) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 256 Unix98 ptys configured
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 32768K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta5-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c596a (rev 09) IDE UDMA33 controller on pci00:07.1
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
hda: ST33221A, ATA DISK drive
hdb: MATSHITA CD-R CW-7582, ATAPI CD/DVD-ROM drive
blk: queue c0401a40, I/O limit 4095Mb (mask 0xffffffff)
hdc: IRQ probe failed (0xfffffff8)
hdc: IRQ probe failed (0xfffffff8)
hdc: no response (status = 0x0a), resetting drive
hdc: IRQ probe failed (0xfffffff8)
hdc: no response (status = 0x0a)
hdd: IRQ probe failed (0xfffffff8)
hdd: IRQ probe failed (0xfffffff8)
hdd: no response (status = 0x0a), resetting drive
hdd: IRQ probe failed (0xfffffff8)
hdd: no response (status = 0x0a)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: attached ide-disk driver.
hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_no_data_intr: error=0x04 { DriveStatusError }
hda: 6303024 sectors (3227 MB) w/128KiB Cache, CHS=1563/64/63, UDMA(33)
Partition check:
/dev/ide/host0/bus0/target0/lun0:ldm_validate_partition_table(): Found an MS -DOS partition table, not a dynamic disk.
p1 p2
ide: late registration of driver.
Initializing Cryptographic API
IEEE 802.2 LLC for Linux 2.1 © 1996 Tim Alpaerts
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: squashfs filesystem found at block 0
RAMDISK: Loading 4668 blocks [1 disk] into ram disk… done.
Freeing initrd memory: 4668k freed
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
SCSI subsystem driver Revision: 1.00
hdb: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: MATSHITA Model: CD-R CW-7582 Rev: 1.10
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 8x/8x writer xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
libata version 0.81 loaded.
libata version 0.81 loaded.
libata version 0.81 loaded.
libata version 0.81 loaded.
libata version 0.81 loaded.
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: linear personality registered as nr 1
md: multipath personality registered as nr 7
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
raid5: measuring checksumming speed
8regs : 1170.000 MB/sec
32regs : 567.200 MB/sec
pIII_sse : 1269.600 MB/sec
pII_mmx : 1467.200 MB/sec
p5_mmx : 1561.200 MB/sec
raid5: using function: pIII_sse (1269.600 MB/sec)
md: raid5 personality registered as nr 4
LVM version 1.0.7(28/03/2003) module loaded
SGI XFS with no debug enabled
SGI XFS Quota Management subsystem
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Trying to move old root to /initrd … failed
Unmounting old root
Trying to free ramdisk memory … okay
Mounted devfs on /dev
Freeing unused kernel memory: 152k freed
Adding Swap: 266100k swap-space (priority -1)
EXT3 FS 2.4-0.9.19+htree+orlov, 19 August 2002 on ide0(3,2), internal journal
Linux agpgart interface v0.99 © Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 123M
agpgart: Detected Via Apollo Pro chipset
agpgart: AGP aperture is 32M @ 0xe4000000
ne2k-pci.c:v1.02 10/19/2000 D. Becker/P. Gortmaker
http://www.scyld.com/network/ne2k-pci.html
PCI: Found IRQ 9 for device 00:12.0
divert: allocating divert_blk for eth0
eth0: RealTek RTL-8029 found at 0xdc00, IRQ 9, 00:40:95:45:43:64.
PCI: Found IRQ 10 for device 00:14.0
PCI: Sharing IRQ 10 with 00:07.2
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 01:51:41 Jan 23 2004
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 10 for device 00:07.2
PCI: Sharing IRQ 10 with 00:14.0
usb-uhci.c: USB UHCI at I/O 0xde00, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI IS APNP enabled
hub.c: new USB device 00:07.2-2, assigned address 2
usb.c: USB device 2 (vend/prod 0x4a9/0x106a) is not claimed by any active driver .
usb.c: registered new driver usblp
printer.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04A9 pid 0x106A
printer.c: v0.11: USB Printer Device Class driver
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
lp0: using parport0 (polling).
inserting floppy driver for 2.4.24-4
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
i2c-core.o: i2c core module version 2.8.0 (20030714)
pcilynx: PCI module init failed
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.17)
libata version 0.81 loaded.
libata version 0.81 loaded.
libata version 0.81 loaded.
libata version 0.81 loaded.
libata version 0.81 loaded.
sr0: CDROM (ioctl) reports ILLEGAL REQUEST.
sr0: CDROM (ioctl) reports ILLEGAL REQUEST.
sr0: CDROM (ioctl) reports ILLEGAL REQUEST.
sr0: CDROM (ioctl) reports ILLEGAL REQUEST.
sr0: CDROM (ioctl) reports ILLEGAL REQUEST.
sr0: CDROM (ioctl) reports ILLEGAL REQUEST.
Real Time Clock Driver v1.10e
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
divert: not allocating divert_blk for non-ethernet device ppp0
mice: PS/2 mouse device common for all mice
sr0: CDROM (ioctl) reports ILLEGAL REQUEST.

(Bocsi, de a „dmesg >>dmesg-kimenet” nem jött öszze…, hogyan kell?)

Köszi

A legutolsó amit kiír az ez:
Kernel 2.4-24.4 (asszem pontosan írtam)
majd ekkor vár egy csomót, semmit sem ír ki, vinyó se megy.
Majd folytatja, ott, hogy : init: valami szám, azt onnan már megy rendesen, tehát írja mit csinál és a zöld „OK

A merevlemez sose akkora, mint amilyennek eladják (a Maxtor közelíti meg mostanában legjobban)
Valójában: 1 Gb = 1024 Mb = 1024*1024 Kb = 1024*1024*1024 byte
A legrendesebbek így számolják: a váltószám 1000
így 15 Gb-os merevlemez 15*1024*1024*1024 Byte = 16 000 000 000Byte õk elosztják 1000*1000*1000-rel így kijön 16 Gb, mivel ez nem osztható 512-vel lefelé kerekítenek.

Ezt tudom, azért írtam csak 3 gigásnak a vinyóm. Mondjuk mindegy, ez a legkisebb problémám most. 🙂

Valóban van már magyarítás. Akkor még nem volt, õszintén nem is érdekelt.

A leírás szerint így kell indítani a firefoxot, hogy mûködjön a magyar nyelv:
firefox -UILocale hu-HU -contentLocale HU
Azt írja instabil és csak úgy ajánlatos átváltani a magyar nyelvre, ha forrásból lett telepítve a firefox.

Igen ezt már próbáltam, de nem jött össze….

Egy utolsó kérdés mára:

Hogy lehet azt megcsinálni amit korábban írtál, hogy a futtathatók közé betenni a firefoxot? Ez gondolom olyan mint mikor dosban az autoexec.bat-ba beírod az elérési utat, hogy tudja hol keresse.