Köszönöm a cimeket de maga a driver megvan Debian,Fedora,Mac,Redhat, Suse, és Win95-xp64-ig.
Engem a telepitése érdekelne,hogy tudom felrakni pl:suse 10.1-re.

Legjobban uhu ra szeretném ami 2,6,9,19 kernel számu

* README
*
* Ralink Tech Inc.
*
* http://www.ralinktech.com
*

=======================================================================
ModelName:
===========
rt61

=======================================================================
Supporting Kernel:
===================
linux kernel 2.4 and 2.6 series.
Tested in Redhat 7.3 or later.

=======================================================================
Description:
=============
This is a linux device driver for Ralink RT61 a/b/g WLAN Card.

=======================================================================
Contents:
=============
./2.4x : Makefile for kernel 2.4 series
./2.6x : Makefile for kernel 2.6 series
*.c : c files
*.h : header files
Makefile.RTL865x : Makefile for big endian platform

=======================================================================
Features:
==========
  This driver implements basic IEEE802.11. Infrastructure and adhoc mode with open or shared or
  WPA-PSK authentication method. NONE, WEP, TKIP and AES encryption.

=======================================================================
Build Instructions: 
====================
For 2.4 series kernel:
a. $tar -xvzf RT61_Linux_STA_Drv_x.x.x.x.tar.gz
    go to „./RT61_Linux_STA_Drv_x.x.x.x/Module” directory.
   
b. Use ‘chmod’ command to change access right of following script files :
  ‘load’, ‘unload’, ‘Configure’

c. run ‘cp ../2.4x/Makefile .’
d. $make config        # config build linux os version

e. $make all            # compile driver source code

f. $cp RT2561.bin /etc/Wireless/RT61STA/ # copy firmware
  $cp RT2561S.bin /etc/Wireless/RT61STA/
  $cp RT2661.bin /etc/Wireless/RT61STA/

g. $load                # load/insmod module(rt61.o)

Note: Script functionality:
load            load module to kernel
unload          unload module from kernel
Configure      retrieve linux version

For 2.6 series kernel:
a.  run ‘cd STA/Module’
        ‘cp ../2.6x/Makefile .’

b. $make all

c. $cp RT2561.bin /etc/Wireless/RT61STA/ # copy firmware
  $cp RT2561S.bin /etc/Wireless/RT61STA/
  $cp RT2661.bin /etc/Wireless/RT61STA/
 
d.  run ‘/sbin/insmod rt61.ko’  (as root)
        ‘/sbin/ifconfig ra0 inet YOUR_IP up’

For big endian platform:
a.  replace Makefile with Makefile.RTL865x
 

=======================================================================
CONFIGURATION: 
====================
RT61 driver can be configured via following interfaces,
i.e. (i)”iwconfig” command, (ii)”iwpriv” command, (iii) configuration file

i)  iwconfig comes with kernel. 
ii) iwpriv usage, please refer to file „iwpriv_usage.txt” for details.
iii)copy configuration file „RT61STA.dat” to /etc/Wireless/RT61STA/RT61STA.dat.

         
Configuration File : RT61STA.dat

---

# Copy this file to /etc/Wireless/RT61STA/RT61STA.dat
# This file is a binary file and will be read on loading rt.o module.
#
# Use „vi -b RT61STA.dat” to modify settings according to your need.
#
# 1.) set NetworkType to „Adhoc” for using Adhoc-mode, otherwise using Infrastructure
# 2.) set Channel to „0” for auto-select on Infrastructure mode
# 3.) set SSID for connecting to your Accss-point.
# 4.) AuthMode can be „WEPAUTO”, „OPEN”, „SHARED”, „WPAPSK”, „WPANONE”
# 5.) EncrypType can be „NONE”, „WEP”, „TKIP”, „AES”
# for more information refer to the Readme file.
#
# The word of „Default” must not be removed
Default
CountryRegion=0
CountryRegionABand=7
WirelessMode=0
SSID=AP350
NetworkType=Infra
Channel=0
AuthMode=OPEN
EncrypType=NONE
DefaultKeyID=1
Key1Type=0
Key1Str=0123456789
Key2Type=0
Key2Str=
Key3Type=0
Key3Str=
Key4Type=0
Key4Str=
WpaPsk=abcdefghijklmnopqrstuvwxyz
TXBurst=0
PktAggregate=0
TurboRate=0
WmmCapable=0
AckPolicy1=0
AckPolicy2=0
AckPolicy3=0
AckPolicy4=0
BGProtection=0
ShortSlot=0
IEEE80211H=0
TxRate=0
RTSThreshold=2347
FragThreshold=2346
PSMode=CAM
TxPreamble=0

---

*NOTE:
WMM parameters
WmmCapable Set it as 1 to turn on WMM Qos support
AckPolicy1~4 Ack policy which support normal Ack or no Ack
(AC_BK, AC_BE, AC_VI, AC_VO)

All WMM parameters do not support iwpriv command but ˇĄWmmCapableˇ¦ˇ¦,
please store all parameter to RT61STA.dat, and restart driver.

---

syntax is ‘Param’=’Value’ and describes below.

1. CountryRegion=value                               
value
0: use 1 ~ 11 Channel
1: use 1 ~ 13 Channel
2: use 10, 11 Channel
3: use 10 ~ 13 Channel
4: use 14 Channel
5: use 1 ~ 14 Channel
6: use 3 ~ 9 Channel
                                       
2. CountryRegionForABand=value     
value
0: use 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 Channel
1: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 Channel
2: use 36, 40, 44, 48, 52, 56, 60, 64 Channel
3: use 52, 56, 60, 64, 149, 153, 157, 161 Channel
4: use 149, 153, 157, 161, 165 Channel
5: use 149, 153, 157, 161 Channel
6: use 36, 40, 44, 48 Channel
7: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 Channel
                                                         
3. SSID=value               
value
0~z, 1~32 ascii characters.
                   
4. WirelessMode=value
value
0: 11b/g mixed,
1: 11B only,
2: 11A only
3: 11a/b/g mixed
4: 11G only
                   
5. TxRate=value
value
0: Auto    //WirelessMode=0~4
1: 1 Mbps //WirelessMode=0 or 1 or 3
        2: 2 Mbps //WirelessMode=0 or 1 or 3
        3: 5.5 Mbps //WirelessMode=0 or 1 or 3
        4: 11 Mbps //WirelessMode=0 or 1 or 3
        5: 6  Mbps  //WirelessMode=0 or 2 or 3 or 4
        6: 9  Mbps  //WirelessMode=0 or 2 or 3 or 4
        7: 12 Mbps  //WirelessMode=0 or 2 or 3 or 4
        8: 18 Mbps  //WirelessMode=0 or 2 or 3 or 4
        9: 24 Mbps  //WirelessMode=0 or 2 or 3 or 4
        10: 36 Mbps  //WirelessMode=0 or 2 or 3 or 4
        11: 48 Mbps  //WirelessMode=0 or 2 or 3 or 4
        12: 54 Mbps  //WirelessMode=0 or 2 or 3 or 4
                                     
6. Channel=value
value
1~14 depends on CountryRegion
                   
7. BGProtection=value
value
0: Auto
1: Always on
2: Always off
                   
8. TxPreamble=value
  value
0:Preamble Long
1:Preamble Short
2:Auto
                   
9. RTSThreshold=value
value
1~2347                                                     
                                                         
10. FragThreshold=value
value     
256~2346
                   
11. TxBurst=value
value
0: Disable
1: Enable

12. NetworkType=value    
value
Infra: infrastructure mode
      Adhoc: adhoc mode

13. AdhocOfdm=value
value
0: Adhere WIFI spec, the Tx MAX rate will be 11Mbps in Adhoc mode
1: Violate WIFI spec, the Tx MAX rate will be 54Mbps in Adhoc mode(b/g mixed)
2: Violate WIFI spec, the Tx MAX rate will be 54Mbps in Adhoc mode(11g only)
                                                                                                                                                                                                                 
14. AuthMode=value
value
OPEN For Open System
SHARED   For Shared key System
WEPAUTO
WPAPSK
WPANONE For Adhoc Security System

15. EncrypType=value
value
NONE For AuthMode=OPEN                   
WEP For AuthMode=OPEN or AuthMode=SHARED
TKIP For AuthMode=WPAPSK                 
AES For AuthMode=WPAPSK                 

16. DefaultKeyID=value
value
1~4

17. Key1=value               
value
10 or 26 hexadecimal characters eg: 012345678
        5 or 13 ascii characters eg: passd                                                                                                                     

18. Key2=value
value
10 or 26 hexadecimal characters eg: 012345678
        5 or 13 ascii characters eg: passd                                                                                                                 

19. Key3=value
value
10 or 26 hexadecimal characters eg: 012345678
        5 or 13 ascii characters eg: passd                                                                                                                   

20. Key4=value
value
10 or 26 hexadecimal characters eg: 012345678
        5 or 13 ascii characters eg: passd                                                                                                                     
                                                       
21. WPAPSK=value             
value
8~63 ASCII  or
64 HEX characters

22. PktAggregate=value
value
0: Disable
1: Enable when the peer supports it

23. TurboRate=value
value
0: Disable
1: Enable 72/100 Mbps whenever applicable
(Not support yet!)
                   
24. WmmCapable=value
value
0: Disable WMM
1: Enable WMM

25. PSMode=value
    value
    0: CAM Constantly Awake Mode
1: Max_PSP Max Power Savings
2: Fast_PSP Power Save Mode

26. IEEE80211H=value
value
0: Disable
1: Enable Spectrum management
(This field can be enable only in A band)

MORE INFORMATION
=================================================================================
If you want for rt61 driver to auto-load at boot time:
A) choose ra0 for first RT61 WLAN card, ra1 for second RT61 WLAN card, etc.
 
B) create(edit) ‘ifcfg-ra0’ file in /etc/sysconfig/network-scripts/,     
  edit( or add the line) in /etc/modules.conf:
      alias ra0 rt61       
 
C) edit(create) the file /etc/sysconfig/network-scripts/ifcfg-ra0 
  DEVICE=’ra0′
  ONBOOT=’yes’   

NOTE:
  if you use dhcp, add this line too .
    BOOTPROTO=’dhcp’

*D) To ease the Default Gateway setting,
    add the line
    GATEWAY=x.x.x.x 
    in /etc/sysconfig/network
  enyi e readme txt je

kicsomagolhatom bárhová
http://www.cens.hu/linux.html
cimen találtam 10.1 re telepitési utmutatot mai a config filet inditsem el ami nem indul vagy a setup-sh-at ami nincs az uhu 2.0 suse 10.1 ismeri rt61 2500nak csak a kezelő progi nem megy fel

nem lenne kompatibilis a linuxal??