Hozzászólások
-
Bejegyzés
-
Időközben találtam egy ilyet is:
http://www.marvec.org/amilo/Ez ellentétben az acehk val fordul 64biten. Be is lehet tölteni.
De összesen annyit tud, hogy parancsal be lehet állítani a rádió állapotot, meg le lehet kérdezni azt…
Valójában a led nem villan fel, a kimeneteken sem vettem észre semmilyen változást.Szia!
Nekem is AMD 64 gépem van, de én openSuse 10.2 X86_64 -t használok
A javahoz a következő csomik kellettek (nekem):
java-1_5_0-sun-plugin
java-1_5_0-sunAz előbbiből tuti nem fogsz X86_64 es csomagot találni én is 32bitest használok.
A Flash nekem meg operával megy. Abból volt 64 bites csomag (nekem) …A másik amit még próbáltam:
Újabb ndiswrapper, másik windriver.
A kimenetek így néznek ki:ifconfig + iwconfig
Code:frosenstar:/home/ferenc # ifconfig
eth1 Link encap:Ethernet HWaddr 00:14:A5:40:EB:C1
UP BROADCAST NOTRAILERS MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:129 Memory:c0200000-c0202000lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:40 errors:0 dropped:0 overruns:0 frame:0
TX packets:40 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2608 (2.5 Kb) TX bytes:2608 (2.5 Kb)frosenstar:/home/ferenc # iwconfig
lo no wireless extensions.eth0 no wireless extensions.
sit0 no wireless extensions.
eth1 IEEE 802.11g ESSID:off/any Nickname:”frosenstar”
Mode:Managed Frequency:2.462 GHz Access Point: Not-Associated
Bit Rate:54 Mb/s Tx-Power:25 dBm
RTS thr:2347 B Fragment thr:2346 B
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0frosenstar:/home/ferenc #
iwlist eth1 scan, dhclient eth1
Code:frosenstar:/ # iwlist eth1 scan
eth1 No scan results
frosenstar:/ # dhclient eth1
Internet Systems Consortium DHCP Client V3.0.5
Copyright 2004-2006 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/Listening on LPF/eth1/00:14:a5:40:eb:c1
Sending on LPF/eth1/00:14:a5:40:eb:c1
Can’t bind to dhcp address: Address already in use
Please make sure there is no other dhcp server
running and that there’s no entry for dhcp or
bootp in /etc/inetd.conf. Also make sure you
are not running HP JetAdmin software, which
includes a bootp server.If you did not get this software from http://ftp.isc.org, please
get the latest from http://ftp.isc.org and install that before
requesting help.If you did get this software from http://ftp.isc.org and have not
yet read the README, please read it before requesting help.
If you intend to request help from the dhcp-server@isc.org
mailing list, please read the section on the README about
submitting bug reports and requests for help.Please do not under any circumstances send requests for
help directly to the authors of this software – please
send them to the appropriate mailing list as described in
the README file.exiting.
Pedig kilőttem az eth0 át mégis azt mondja hogy valami még megy… ???
A kwlan viszont most már hibaüzenet nélkül elindul, de még mindíg nem talál hálózatot…
Akinek van ötlete kérem segítsen!
Kipróbáltam bepe79 firmware -t is. De önmagában ez sem segített, ugyanis van egy kis gond a natív bcm43xx driverrel, amit eddig nem észleltem:
Ha be van töltve és helyén van valamilyen firmware, akkor összeakad az usbs eszközökkel.
Usb s egér, pendrive nem megy…A dmesg idevágó része így néz ki:
Code:powernow-k8: 0 : fid 0x0 (800 MHz), vid 0x16
powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x6
powernow-k8: 2 : fid 0xa (1800 MHz), vid 0x4
eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
NET: Registered protocol family 17
ADDRCONF(NETDEV_UP): eth1: link is not ready
audit(1171057337.631:2): audit_pid=4149 old=0 by auid=4294967295
psmouse.c: GlidePoint at isa0060/serio4/input0 lost synchronization, throwing 1 bytes away.
psmouse.c: resync failed, issuing reconnect request
ndiswrapper: device eth1 removed
usbcore: deregistering driver ndiswrapper
NTFS-fs error (device hda1): ntfs_nlstoucs(): Name using character set utf8 contains characters that cannot be converted to Unicode.
NTFS-fs error (device hda1): ntfs_lookup(): Failed to convert name to Unicode.
ieee80211_crypt: registered algorithm ‘NULL’
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation
bcm43xx driver
PCI: Enabling device 0000:08:0a.0 (0000 -> 0002)
bcm43xx: Chip ID 0x4318, rev 0x2
bcm43xx: Number of cores: 4
bcm43xx: Core 0: ID 0x800, rev 0xd, vendor 0x4243, enabled
bcm43xx: Core 1: ID 0x812, rev 0x9, vendor 0x4243, disabled
bcm43xx: Core 2: ID 0x804, rev 0xc, vendor 0x4243, enabled
bcm43xx: Core 3: ID 0x80d, rev 0x7, vendor 0x4243, enabled
bcm43xx: PHY connected
bcm43xx: Detected PHY: Version: 3, Type 2, Revision 7
bcm43xx: Detected Radio: ID: 8205017f (Manuf: 17f Ver: 2050 Rev: 8)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
bcm43xx: set security called, .level = 0, .enabled = 0, .encrypt = 0
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Associate: failed to initiate scan. Is device up?
bcm43xx: PHY connected
bcm43xx: Microcode rev 0x127, pl 0xe (2005-04-18 02:36:27)
bcm43xx: Radio turned on
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: 32-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at: drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1496:bcm43xx_find_lopair()
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
ADDRCONF(NETDEV_UP): eth1: link is not ready
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Unable to find matching network after scan!
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Associate: Scanning for networks first.
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
SoftMAC: Unable to find matching network after scan!
irq 145: nobody cared (try booting with the "irqpoll" option)Call Trace:
[] __report_bad_irq+0x30/0x7d
[] note_interrupt+0x1e3/0x224
[] __do_IRQ+0xc7/0x105
[] cache_reap+0x0/0x21c
[] do_IRQ+0x65/0x73
[] ret_from_intr+0x0/0xa
[] cache_reap+0x6a/0x21c
[] run_workqueue+0x94/0xe5
[] worker_thread+0x0/0x122
[] worker_thread+0xf0/0x122
[] default_wake_function+0x0/0xe
[] kthread+0xec/0x120
[] child_rip+0xa/0x12
[] dummycon_dummy+0x0/0x3
[] kthread+0x0/0x120
[] child_rip+0x0/0x12handlers:
[] (usb_hcd_irq+0x0/0x55 [usbcore])
[] (usb_hcd_irq+0x0/0x55 [usbcore])
[] (usb_hcd_irq+0x0/0x55 [usbcore])
Disabling IRQ #145
SoftMAC: Start scanning with channel: 1
SoftMAC: Scanning 14 channels
SoftMAC: Scanning finished
bcm43xx: Radio turned off
bcm43xx: DMA-32 0x0200 (RX) max used slots: 0/64
bcm43xx: DMA-32 0x02A0 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0280 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0220 (TX) max used slots: 84/512
bcm43xx: DMA-32 0x0200 (TX) max used slots: 0/512
frosenstar:/l #
irq ütközés lenne? Próbáltam az irqpoll boot paramétert.
Ekkor ha helyén a firmware és töltődik a bcm43xx, a bootolás megáll az eth1 dhcp kérésnél…Köszi a kimeneteket.
Egyébként én is megpróbáltam a SimplyMEPIS 6.0-4 Beta-4_amd64 et, de egyszerűen be se bootol.
Normál boot al fekete képernyő után kikapcsol.
A többinél, meg vagy megáll valahol félúton a bootolás, vagy kernel panic…Visszakanyarodva… Egyébként elég érdekes, hogy ndiswrappert használsz, és mégis helyén van a firmware.
Ami viszont még érdekesebb, hogy milyen firmware lehet ez amit te használsz???Mert én eddig kettőről tudtam, az egyik az Broadcom gyártmány, a másik meg Microsoft.
Nekem per pillanat az utóbbi van fent, ami így néz ki:
Code:frosenstar:/lib/firmware # ls -la
összesen 860
drwxr-xr-x 2 root root 4096 febr 9 12.06 .
drwxr-xr-x 10 root root 4096 febr 6 02.39 ..
-rw-r–r– 1 root root 3504 febr 9 12.06 bcm43xx_initval01.fw
-rw-r–r– 1 root root 16 febr 9 12.06 bcm43xx_initval02.fw
-rw-r–r– 1 root root 3504 febr 9 12.06 bcm43xx_initval03.fw
-rw-r–r– 1 root root 16 febr 9 12.06 bcm43xx_initval04.fw
-rw-r–r– 1 root root 2536 febr 9 12.06 bcm43xx_initval05.fw
-rw-r–r– 1 root root 248 febr 9 12.06 bcm43xx_initval06.fw
-rw-r–r– 1 root root 2536 febr 9 12.06 bcm43xx_initval07.fw
-rw-r–r– 1 root root 2536 febr 9 12.06 bcm43xx_initval08.fw
-rw-r–r– 1 root root 248 febr 9 12.06 bcm43xx_initval09.fw
-rw-r–r– 1 root root 248 febr 9 12.06 bcm43xx_initval10.fw
-rw-r–r– 1 root root 16216 febr 9 12.06 bcm43xx_microcode2.fw
-rw-r–r– 1 root root 19968 febr 9 12.06 bcm43xx_microcode4.fw
-rw-r–r– 1 root root 22528 febr 9 12.06 bcm43xx_microcode5.fw
-rw-r–r– 1 root root 1312 febr 9 12.06 bcm43xx_pcm4.fw
-rw-r–r– 1 root root 1312 febr 9 12.06 bcm43xx_pcm5.fw
-rw-r–r– 1 root root 76802 nov 29 14.51 ql2100_fw.bin
-rw-r–r– 1 root root 84566 nov 29 14.51 ql2200_fw.bin
-rw-r–r– 1 root root 121872 nov 29 14.51 ql2300_fw.bin
-rw-r–r– 1 root root 131464 nov 29 14.51 ql2322_fw.bin
-rw-r–r– 1 root root 196900 nov 29 14.51 ql2400_fw.bin
-rw-r–r– 1 root root 112494 nov 29 14.51 ql6312_fw.bin
frosenstar:/lib/firmware #De ha a broadcomot használom, akkor sincs ilyenem:
bcm43xx_microcode11.fwDe neked van! Ez hogy lehet??? Nagyon misztikus.
Érdekes… ndiswrapperes megoldás.
Ezeket a kimeneteket meg tudnád nézni még ha megkérlek:
1, ndiswrapper -l
2, ifconfig
3, iwconfig
4, hwinfo –wlanbepe79 wrote:Hi `ya! Nekem 64 bites SimplyMepis (Mepis) van fent a laptopomon (64 bites AMD Turion proci) most, es csont nelkul mukodik a WLAN. Raadasul nekem is Broadcom wlan kartyam van az Acer notebookomban, egy Broadcom bcm4318-as chipsetes. SimplyMepis 6.0-4 Beta 4 a legujabb, es varhatoan 2 nap mulva jon ki a vegleges, final SimplyMepis 6.0-4Ez örvendetes, de kérlek mond el mit használ bcm43xx? vagy ndiswrappert windrivert milyet használsz? Gondolom acerhk modulod neked sincs.
A bcm43xx driverrel kicsit tovább jutottam:
/etc/modprobe.d/blacklist és a
/etc/sysconfig/hardware/hwcfg-bus-pci-xxx et visszaállítottam.fwcutterrel a bcmwl564.sys -t helyre raktam
modprobe bcm43xx
hibaüzenet nincs
Ekkor lsmod:
Code:frosenstar:/home/ferenc # lsmod
Module Size Used by
joydev 28160 0
xt_pkttype 18816 3
ipt_LOG 23808 8
xt_limit 20224 8
snd_pcm_oss 71680 0
snd_mixer_oss 35840 1 snd_pcm_oss
snd_seq 82976 0
snd_seq_device 26516 1 snd_seq
af_packet 57356 8
cpufreq_conservative 25608 0
cpufreq_ondemand 24592 0
cpufreq_userspace 24064 0
cpufreq_powersave 18688 0
powernow_k8 32416 0
freq_table 22912 1 powernow_k8
ip6t_REJECT 22528 3
xt_tcpudp 20352 3
ipt_REJECT 22528 3
xt_state 19200 12
iptable_mangle 19840 0
iptable_nat 24964 0
ip_nat 37804 1 iptable_nat
iptable_filter 19968 1
ip6table_mangle 19456 0
ip_conntrack 78372 3 xt_state,iptable_nat,ip_nat
nfnetlink 24648 2 ip_nat,ip_conntrack
ip_tables 39400 3 iptable_mangle,iptable_nat,iptable_filter
ip6table_filter 19840 1
ip6_tables 33352 2 ip6table_mangle,ip6table_filter
x_tables 37384 10 xt_pkttype,ipt_LOG,xt_limit,ip6t_REJECT,xt_tcpudp,ipt_REJECT,xt_state,iptable_nat,ip_tables,ip6_tables
ipv6 357728 15 ip6t_REJECT
apparmor 74264 0
aamatch_pcre 31232 1 apparmor
nls_utf8 18944 1
ntfs 209032 1
loop 34064 0
dm_mod 81872 0
usbhid 69792 0
bcm43xx 451328 0
firmware_class 28288 1 bcm43xx
8139too 46720 0
ide_cd 59680 0
cdrom 54056 1 ide_cd
ohci1394 52040 0
ieee80211softmac 52608 1 bcm43xx
ehci_hcd 51080 0
mii 22912 1 8139too
shpchp 56492 0
ieee1394 130552 1 ohci1394
ohci_hcd 38404 0
ieee80211 50248 2 bcm43xx,ieee80211softmac
ieee80211_crypt 23680 1 ieee80211
pci_hotplug 52228 1 shpchp
usbcore 148064 3 usbhid,ehci_hcd,ohci_hcd
i2c_piix4 26508 0
i2c_core 41472 1 i2c_piix4
snd_hda_intel 37660 4
snd_hda_codec 220160 1 snd_hda_intel
snd_pcm 115464 4 snd_pcm_oss,snd_hda_intel,snd_hda_codec
snd_timer 44680 3 snd_seq,snd_pcm
snd 89384 14 snd_pcm_oss,snd_mixer_oss,snd_seq,snd_seq_device,snd_hda_intel,snd_hda_codec,snd_pcm,snd_timer
soundcore 28192 1 snd
snd_page_alloc 27792 2 snd_hda_intel,snd_pcm
ext3 167696 2
mbcache 27016 1 ext3
jbd 90872 1 ext3
edd 27912 0
processor 53992 1 powernow_k8
atiixp 23568 0 [permanent]
ide_disk 34304 5
ide_core 174720 3 ide_cd,atiixp,ide_disk
frosenstar:/home/ferenc #ifconfig+iwconfig (essid -t én állítottam be) :
Code:frosenstar:/home/ferenc # ifconfig
eth1 Link encap:Ethernet HWaddr 00:14:A5:40:EB:C1
UP BROADCAST NOTRAILERS MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:154 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:6594 (6.4 Kb)
Interrupt:129 Base address:0xc000lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:192 errors:0 dropped:0 overruns:0 frame:0
TX packets:192 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:14348 (14.0 Kb) TX bytes:14348 (14.0 Kb)frosenstar:/home/ferenc # iwconfig
lo no wireless extensions.eth0 no wireless extensions.
eth1 IEEE 802.11b/g ESSID:”SMC” Nickname:”frosenstar”
Mode:Managed Frequency=2.484 GHz Access Point: Invalid
Bit Rate=1 Mb/s Tx-Power=18 dBm
RTS thr:off Fragment thr:off
Encryption key:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0sit0 no wireless extensions.
frosenstar:/home/ferenc #
Az apparmort kikapcsoltam, hogy ne zavarjon.
Ha beállítok egy ipcímet, akkor azt tudom pingelni.
De mást nem igazán tudok csinálni…
ping:Code:frosenstar:/home/ferenc # ifconfig eth1 192.168.1.1 up
frosenstar:/home/ferenc # ping 192.168.1.1
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=0.072 ms
64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=0.058 ms
64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=0.059 ms
64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=0.060 ms
64 bytes from 192.168.1.1: icmp_seq=5 ttl=64 time=0.061 ms— 192.168.1.1 ping statistics —
5 packets transmitted, 5 received, 0% packet loss, time 3998ms
rtt min/avg/max/mdev = 0.058/0.062/0.072/0.005 ms
frosenstar:/home/ferenc #iwlist:
Code:frosenstar:/home/ferenc # iwlist eth1 scan
eth1 No scan results
frosenstar:/home/ferenc #dhclient:
Code:frosenstar:/home/ferenc # dhclient eth1
Internet Systems Consortium DHCP Client V3.0.5
Copyright 2004-2006 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/Listening on LPF/eth1/00:14:a5:40:eb:c1
Sending on LPF/eth1/00:14:a5:40:eb:c1
Sending on Socket/fallback
DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 5
DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 13
DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 16
DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 9
DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 18
No DHCPOFFERS received.
No working leases in persistent database – sleeping.
frosenstar:/home/ferenc #Feltettem a kwlant is, de azzal se jutottam tovább.
Akinek van ötlete a megoldásra kérem írjon!
Előszöris az ndiswrapper -es próbálkozásom röviden:
Suse DVD ről ndiswrapper csamagok fel, driver kitömörít,
/etc/modprobe.d/blacklist és a
/etc/sysconfig/hardware/hwcfg-bus-pci-xxx et módosítottam…ndiswrapper -i netbc564.inf
modprobe ndiswrapper
Hibaüzenet nincs. restart
Ekkor lsmod:Code:frosenstar:/home/ferenc # lsmod
Module Size Used by
joydev 28160 0
xt_pkttype 18816 3
ipt_LOG 23808 8
xt_limit 20224 8
snd_pcm_oss 71680 0
snd_mixer_oss 35840 1 snd_pcm_oss
snd_seq 82976 0
snd_seq_device 26516 1 snd_seq
af_packet 57356 2
cpufreq_conservative 25608 0
cpufreq_ondemand 24592 0
cpufreq_userspace 24064 0
cpufreq_powersave 18688 0
powernow_k8 32416 0
freq_table 22912 1 powernow_k8
ip6t_REJECT 22528 3
xt_tcpudp 20352 3
ipt_REJECT 22528 3
xt_state 19200 12
iptable_mangle 19840 0
iptable_nat 24964 0
ip_nat 37804 1 iptable_nat
iptable_filter 19968 1
ip6table_mangle 19456 0
ip_conntrack 78372 3 xt_state,iptable_nat,ip_nat
nfnetlink 24648 2 ip_nat,ip_conntrack
ip_tables 39400 3 iptable_mangle,iptable_nat,iptable_filter
ip6table_filter 19840 1
ip6_tables 33352 2 ip6table_mangle,ip6table_filter
x_tables 37384 10 xt_pkttype,ipt_LOG,xt_limit,ip6t_REJECT,xt_tcpudp,ipt_REJECT,xt_state,iptable_nat,ip_tables,ip6_tables
ipv6 357728 15 ip6t_REJECT
nls_utf8 18944 1
ntfs 209032 1
loop 34064 0
dm_mod 81872 0
usbhid 69792 0
ndiswrapper 249512 0
8139too 46720 0
ohci1394 52040 0
ide_cd 59680 0
cdrom 54056 1 ide_cd
mii 22912 1 8139too
ieee1394 130552 1 ohci1394
snd_hda_intel 37660 4
snd_hda_codec 220160 1 snd_hda_intel
snd_pcm 115464 4 snd_pcm_oss,snd_hda_intel,snd_hda_codec
snd_timer 44680 3 snd_seq,snd_pcm
snd 89384 14 snd_pcm_oss,snd_mixer_oss,snd_seq,snd_seq_device,snd_hda_intel,snd_hda_codec,snd_pcm,snd_timer
soundcore 28192 1 snd
snd_page_alloc 27792 2 snd_hda_intel,snd_pcm
shpchp 56492 0
pci_hotplug 52228 1 shpchp
i2c_piix4 26508 0
ehci_hcd 51080 0
ohci_hcd 38404 0
i2c_core 41472 1 i2c_piix4
usbcore 148064 4 usbhid,ndiswrapper,ehci_hcd,ohci_hcd
ext3 167696 2
mbcache 27016 1 ext3
jbd 90872 1 ext3
edd 27912 0
processor 53992 1 powernow_k8
atiixp 23568 0 [permanent]
ide_disk 34304 5
ide_core 174720 3 ide_cd,atiixp,ide_disk
frosenstar:/home/ferenc #ifconfig:
Code:ferenc@frosenstar:~> su
Jelsz├│:
frosenstar:/home/ferenc # ifconfig
eth0 Link encap:Ethernet HWaddr 00:40:CA:D9:25:83
UP BROADCAST NOTRAILERS MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:137 Base address:0x8800lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:40 errors:0 dropped:0 overruns:0 frame:0
TX packets:40 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2608 (2.5 Kb) TX bytes:2608 (2.5 Kb)frosenstar:/home/ferenc #
iwconfig:
Code:[
frosenstar:/home/ferenc # iwconfig
lo no wireless extensions.eth0 no wireless extensions.
sit0 no wireless extensions.
frosenstar:/home/ferenc # /code]
igazából innentől kezdve itt megállt a tudomány…
semmilyen ifconfig, vagy iwconfig os parancs nem használt.
más driverekkel is próbálkoztam de nem több sikerrel.
legutóbbi hsz