gabcsi

Hozzászólások

10 bejegyzés megtekintése - 11-20 / 58
  • Szerző
    Bejegyzés
  • Hozzászólás: Bad blokks #1958445
    gabcsi
    Felhasználó

      Tud ebbõl vki kihámozni valamit?
      Részleteibe kommentezve!
      Elõre is köszönöm.

      dark:~# smartctl -a /dev/hdc
      smartctl version 5.30 Copyright © 2002-4 Bruce Allen
      Home page is http://smartmontools.sourceforge.net/

      === START OF INFORMATION SECTION ===
      Device Model: MAXTOR 4K040H2
      Serial Number: 672132369028
      Firmware Version: A08.1500
      Device is: Not in smartctl database [for details use: -P showall]
      ATA Version is: 5
      ATA Standard is: ATA/ATAPI-5 T13 1321D revision 1
      Local Time is: Wed Jul 7 10:48:26 2004 CEST
      SMART support is: Available – device has SMART capability.
      SMART support is: Enabled

      === START OF READ SMART DATA SECTION ===
      SMART overall-health self-assessment test result: PASSED

      General SMART Values:
      Offline data collection status: (0x00) Offline data collection activity was
      never started.
      Auto Offline Data Collection: Disabled.
      Self-test execution status: ( 0) The previous self-test routine completed
      without error or no self-test has ever
      been run.
      Total time to complete Offline
      data collection: ( 44) seconds.
      Offline data collection
      capabilities: (0x1b) SMART execute Offline immediate.
      Auto Offline data collection on/off support.
      Suspend Offline collection upon new
      command.
      Offline surface scan supported.
      Self-test supported.
      No Conveyance Self-test supported.
      No Selective Self-test supported.
      SMART capabilities: (0x0003) Saves SMART data before entering
      power-saving mode.
      Supports SMART auto save timer.
      Error logging capability: (0x01) Error logging supported.
      No General Purpose Logging support.
      Short self-test routine
      recommended polling time: ( 2) minutes.
      Extended self-test routine
      recommended polling time: ( 26) minutes.

      SMART Attributes Data Structure revision number: 11
      Vendor Specific SMART Attributes with Thresholds:
      ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
      1 Raw_Read_Error_Rate 0x0029 100 253 020 Pre-fail Offline – 0
      3 Spin_Up_Time 0x0027 086 084 020 Pre-fail Always – 1866
      4 Start_Stop_Count 0x0032 097 097 008 Old_age Always – 2330
      5 Reallocated_Sector_Ct 0x0033 100 100 020 Pre-fail Always – 0
      7 Seek_Error_Rate 0x000b 100 100 023 Pre-fail Always – 0
      9 Power_On_Hours 0x0012 094 094 001 Old_age Always – 4202
      10 Spin_Retry_Count 0x0026 100 100 000 Old_age Always – 0
      11 Calibration_Retry_Count 0x0013 100 100 020 Pre-fail Always – 0
      12 Power_Cycle_Count 0x0032 098 098 008 Old_age Always – 1640
      13 Read_Soft_Error_Rate 0x000b 100 100 023 Pre-fail Always – 0
      194 Temperature_Celsius 0x0022 089 082 042 Old_age Always – 30
      195 Hardware_ECC_Recovered 0x001a 017 003 000 Old_age Always – 510252892
      196 Reallocated_Event_Count 0x0010 100 253 020 Old_age Offline – 0
      197 Current_Pending_Sector 0x0032 100 100 020 Old_age Always – 0
      198 Offline_Uncorrectable 0x0010 100 253 000 Old_age Offline – 0
      199 UDMA_CRC_Error_Count 0x001a 163 163 000 Old_age Always – 37

      SMART Error Log Version: 1
      ATA Error Count: 142 (device log contains only the most recent five errors)
      CR = Command Register [HEX]
      FR = Features Register [HEX]
      SC = Sector Count Register [HEX]
      SN = Sector Number Register [HEX]
      CL = Cylinder Low Register [HEX]
      CH = Cylinder High Register [HEX]
      DH = Device/Head Register [HEX]
      DC = Device Command Register [HEX]
      ER = Error register [HEX]
      ST = Status register [HEX]
      Timestamp = decimal seconds since the previous disk power-on.
      Note: timestamp „wraps” after 2^32 msec = 49.710 days.

      Error 142 occurred at disk power-on lifetime: 1515 hours
      When the command that caused the error occurred, the device was in an unknown state.

      After command completion occurred, registers were:
      ER ST SC SN CL CH DH
      — — — — — — —
      40 59 07 60 be 01 e0 Error: UNC 7 sectors at LBA = 0x0001be60 = 114272

      Commands leading to the command that caused the error were:
      CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
      — — — — — — — —



      c8 00 08 5f be 01 e0 01 86.333 READ DMA
      c8 01 08 37 be 01 e0 00 86.333 READ DMA
      c8 01 08 27 be 01 e0 00 86.332 READ DMA
      c8 01 08 0f 57 0e e0 00 86.332 READ DMA
      c8 00 08 c7 00 00 e0 00 86.318 READ DMA

      Error 141 occurred at disk power-on lifetime: 1515 hours
      When the command that caused the error occurred, the device was in an unknown state.

      After command completion occurred, registers were:
      ER ST SC SN CL CH DH
      — — — — — — —
      40 59 07 60 be 01 e0 Error: UNC 7 sectors at LBA = 0x0001be60 = 114272

      Commands leading to the command that caused the error were:
      CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
      — — — — — — — —



      c8 00 08 5f be 01 e0 01 296.968 READ DMA
      ca 00 10 47 a2 03 e0 03 296.968 WRITE DMA
      c8 00 08 e7 81 05 e0 05 296.953 READ DMA
      ca 00 08 07 a2 03 e0 03 296.953 WRITE DMA
      ca 00 20 d7 a1 03 e0 03 296.952 WRITE DMA

      Error 140 occurred at disk power-on lifetime: 1515 hours
      When the command that caused the error occurred, the device was in an unknown state.

      After command completion occurred, registers were:
      ER ST SC SN CL CH DH
      — — — — — — —
      40 59 07 60 be 01 e0 Error: UNC 7 sectors at LBA = 0x0001be60 = 114272

      Commands leading to the command that caused the error were:
      CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
      — — — — — — — —



      c8 00 08 5f be 01 e0 01 292.757 READ DMA
      ca 00 03 7e 22 00 e0 00 292.757 WRITE DMA
      ca 00 01 7c 22 00 e0 00 292.756 WRITE DMA
      ca 00 02 71 22 00 e0 00 292.756 WRITE DMA
      ca 00 02 6b 22 00 e0 00 292.756 WRITE DMA

      Error 139 occurred at disk power-on lifetime: 1515 hours
      When the command that caused the error occurred, the device was in an unknown state.

      After command completion occurred, registers were:
      ER ST SC SN CL CH DH
      — — — — — — —
      40 59 07 60 be 01 e0 Error: UNC 7 sectors at LBA = 0x0001be60 = 114272

      Commands leading to the command that caused the error were:
      CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
      — — — — — — — —



      c8 00 08 5f be 01 e0 01 288.461 READ DMA
      c8 00 08 ff 54 02 e0 02 288.448 READ DMA
      ca 00 40 af 6c 03 e0 03 288.448 WRITE DMA
      ca 00 40 ef 6c 03 e0 03 288.447 WRITE DMA
      ca 00 40 2f 6d 03 e0 03 288.446 WRITE DMA

      Error 138 occurred at disk power-on lifetime: 1515 hours
      When the command that caused the error occurred, the device was in an unknown state.

      After command completion occurred, registers were:
      ER ST SC SN CL CH DH
      — — — — — — —
      40 59 07 60 be 01 e0 Error: UNC 7 sectors at LBA = 0x0001be60 = 114272

      Commands leading to the command that caused the error were:
      CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
      — — — — — — — —



      c8 00 08 5f be 01 e0 01 283.972 READ DMA
      ca 00 40 ef 6b 03 e0 03 283.971 WRITE DMA
      ca 00 40 6f 6c 03 e0 03 283.971 WRITE DMA
      ca 00 40 2f 6c 03 e0 03 283.970 WRITE DMA
      c8 01 08 37 52 35 e0 00 283.970 READ DMA

      SMART Self-test log structure revision number 1
      No self-tests have been logged. [To run self-tests, use: smartctl -t]

      Hozzászólás: Abev.exe #1958286
      gabcsi
      Felhasználó

        Hali!

        Próbáld ki debian SID alatt a wine-vel!
        Tökéletesen mûködik, csak veszett lassú a PII-1.1GHz gépeke is, meg a nyomtatás egy kicsit zûrös!

        Hozzászólás: SID #1927495
        gabcsi
        Felhasználó

          xterm alatt VIL

          Hozzászólás: SID #1927493
          gabcsi
          Felhasználó

            X felület, KDE !
            Terminal alatt OK, xterm alatt NINCS num-lock!

            ### BEGIN DEBCONF SECTION
            # XF86Config-4 (XFree86 server configuration file) generated by dexconf, the
            # Debian X Configuration tool, using values from the debconf database.
            #
            # Edit this file with caution, and see the XF86Config-4 manual page.
            # (Type „man XF86Config-4” at the shell prompt.)
            #
            # If you want your changes to this file preserved by dexconf, only make changes
            # before the „### BEGIN DEBCONF SECTION” line above, and/or after the
            # „### END DEBCONF SECTION” line below.
            #
            # To change things within the debconf section, run the command:
            # dpkg-reconfigure xserver-xfree86
            # as root. Also see „How do I add custom sections to a dexconf-generated
            # XF86Config or XF86Config-4 file?” in /usr/share/doc/xfree86-common/FAQ.gz.

            Section „Files”
            FontPath „unix/:7100” # local font server
            # if the local font server has problems, we can fall back on these
            FontPath „/usr/lib/X11/fonts/Type1”
            FontPath „/usr/lib/X11/fonts/CID”
            FontPath „/usr/lib/X11/fonts/Speedo”
            FontPath „/usr/lib/X11/fonts/misc”
            FontPath „/usr/lib/X11/fonts/cyrillic”
            FontPath „/usr/lib/X11/fonts/100dpi”
            FontPath „/usr/lib/X11/fonts/75dpi”
            EndSection

            Section „Module”
            # Load „GLcore”
            Load „bitmap”
            Load „dbe”
            Load „ddc”
            Load „dri”
            Load „extmod”
            Load „freetype”
            Load „glx”
            Load „int10”
            Load „record”
            # Load „speedo”
            Load „type1”
            Load „vbe”
            EndSection

            Section „InputDevice”
            Identifier „Generic Keyboard”
            Driver „keyboard”
            Option „CoreKeyboard”
            Option „XkbRules” „xfree86”
            Option „XkbModel” „pc104”
            Option „XkbLayout” „hu”
            EndSection

            Section „InputDevice”
            Identifier „Configured Mouse”
            Driver „mouse”
            Option „CorePointer”
            Option „Device” „/dev/ttyS0”
            Option „Protocol” „Microsoft”
            Option „Emulate3Buttons” „true”
            Option „ZAxisMapping” „4 5”
            EndSection

            Section „InputDevice”
            Identifier „Generic Mouse”
            Driver „mouse”
            Option „SendCoreEvents” „true”
            Option „Device” „/dev/input/mice”
            Option „Protocol” „ImPS/2”
            Option „Emulate3Buttons” „true”
            Option „ZAxisMapping” „4 5”
            EndSection

            Section „Device”
            Identifier „rage 128”
            Driver „r128”
            EndSection

            Section „Monitor”
            Identifier „Generic Monitor”
            HorizSync 28-50
            VertRefresh 43-60
            Option „DPMS”
            EndSection

            Section „Screen”
            Identifier „Default Screen”
            Device „rage 128”
            Monitor „Generic Monitor”
            DefaultDepth 24
            SubSection „Display”
            Depth 1
            Modes „800×600” „640×480”
            EndSubSection
            SubSection „Display”
            Depth 4
            Modes „800×600” „640×480”
            EndSubSection
            SubSection „Display”
            Depth 8
            Modes „800×600” „640×480”
            EndSubSection
            SubSection „Display”
            Depth 15
            Modes „800×600” „640×480”
            EndSubSection
            SubSection „Display”
            Depth 16
            Modes „800×600” „640×480”
            EndSubSection
            SubSection „Display”
            Depth 24
            Modes „800×600” „640×480”
            EndSubSection
            EndSection

            Section „ServerLayout”
            Identifier „Default Layout”
            Screen „Default Screen”
            InputDevice „Generic Keyboard”
            InputDevice „Configured Mouse”
            # InputDevice „Generic Mouse”
            EndSection

            Section „DRI”
            Mode 0666
            EndSection

            ### END DEBCONF SECTION

            Köszi.
            gab.

            Hozzászólás: C-fejlesztés, KDevelop, stb… #1915681
            gabcsi
            Felhasználó

              Hali!

              Kdevelop alatt szögelgetem a programomat, amely a MSQL adatbázist használja!
              Azt szeretném elérni, hogy ne a program kezelje a felhasználókat (egy kicsit meredek) hanem a mysql! A biztonság csak azon van, hogy némelyik felhasználó csak olvasni tudja az adatbázist, mások írhatják is a prg-n keresztül.
              A célom, hogy a usernek ne kellejen mégegyszer beírnia a jelszavát és a felhasználói nevét!
              Hogyan tudom áthozni a prg.-omba a felhasználói nevét indítási paraméter megadása nélkül?
              A jelszót amit használt a loginkor, hogyan lehet felhasználni a mysql belépéshez?
              Lehetséges ez egyátalán v. milyen módon szokták ezt lekezelni?

              Elõre is köszönöm!
              gab.

              Hozzászólás: SID #1927491
              gabcsi
              Felhasználó
                Hozzászólás: SID #1927489
                gabcsi
                Felhasználó

                  Hali!

                  Fellow, akkor sem megy a num-lock billentyûm és nagyon idegesít!!
                  Kérlek segíts a numlockx nem segített!
                  A capsLock is furán viselkedik!

                  Kérlek segíts!!

                  gabcsi.

                  Hozzászólás: SID #1927482
                  gabcsi
                  Felhasználó

                    Hali!

                    A múltheti SID frissítésem óta sajnos nem mûködik a num-Lock billentyûm funkciója!
                    Sehogy sem tudom kihozni belõle a numerikus karaktereket!
                    Tud ebben vki segíteni, hogy hol kezdjek hozzá?

                    gab.

                    gabcsi
                    Felhasználó

                      Gondolj bele 😆 😆

                      Pénztárgép+(olcsó)számítógép+linux+sorosport (összekötve) -]

                      gabcsi
                      Felhasználó

                        Sok fölösleges szócséplés!
                        Lafisoft!
                        Az APEH-nak semmi köze a prg.-hoz! A szoftvernek a törvényben szabályzott feltételeket kell teljesítenie, NEM KELL ELFOGADTATNI stb.!
                        Egy fontos dolog van, LEGYEN A HASZN

                      10 bejegyzés megtekintése - 11-20 / 58