„Never give up and never surrender”

naszóval csak babrálom a linuxot … amire jutottam …

eth0 -t most már nvnet uralja …

eth0 Link encap:Ethernet HWaddr 00:11:D8:A4:5A:74
inet6 addr: fe80::211:d8ff:fea4:5a74/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2709 errors:0 dropped:0 overruns:0 frame:0
TX packets:37 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:165945 (162.0 KiB) TX bytes:1330 (1.2 KiB)
Interrupt:5

modulok:
pppoe 16256 0
pppox 4624 1 pppoe
ipv6 279584 12
ppp_generic 29408 2 pppoe,pppox
slhc 8064 1 ppp_generic
tuner 24420 0
tvaudio 24800 0
bttv 179280 0
video_buf 25540 1 bttv
firmware_class 11648 1 bttv
i2c_algo_bit 10248 1 bttv
v4l2_common 7680 1 bttv
btcx_risc 5640 1 bttv
videodev 12288 1 bttv
eth1394 22800 0
nvnet 75752 0
nvsound 1713132 0
ohci1394 36420 0
sbp2 27656 0
ieee1394 120920 3 eth1394,ohci1394,sbp2

/etc/network/interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network int
auto lo
iface lo inet loopback

auto dsl-provider
iface dsl-provider inet ppp
provider dsl-provider
# please do not modify the following line
pre-up /sbin/ifconfig eth0 up # line maintained by pppoeconf

debian:/home/juuzer# pppd
pppd: The remote system is required to authenticate itself
pppd: but I couldn’t find any suitable secret (password) for it to use to do so.
pppd: (None of the available passwords would let it use an IP address.)

kérdéseim:
1. chello + motorola modem alaplapi hálókártyába csatlakozva, bejelentkezés nincs, mivel chello ugy mûködik, hogy modem regisztrálva van upc-nél és sorozatszám alpján megy forgalommérés + minden egyéb tehát pppd üzenetével igazá nem tudok mit kezdeni lehet hogy elconfigoltam? szóval jelszó nem kell az tuti..

2.
/etc/network/interfaces -ben
az: „iface dsl-povider inet ppp” helyet nem „iface dsl-provider inet pppoe” -nek kéne lennie

3.
eth0-nál ” RX bytes:165945 (162.0 KiB) TX bytes:1330 (1.2 KiB)”
ez a küldött és fogadott adatokat jelenti-e ? (ha igen akkor csak van valami nem? 😀 )

kösz elõre is

ifconfig: ( a smile-kat nem én tettem be a fórumból adódik amugy sima”b+)” )
eth0 Link encap:UNSPEC HWaddr00-11-D8-00-00-18-EB-CE-00-00-00-00-00-00-00-00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

eth1 Link encap:Ethernet HWaddr 00:11:D8:A4:5A:74
inet6 addr: fe80::211:d8ff:fea4:5a74/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2322 errors:0 dropped:0 overruns:0 frame:0
TX packets:23 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:143934 (140.5 KiB) TX bytes:882 (882.0 B)
Interrupt:5

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:68 errors:0 dropped:0 overruns:0 frame:0
TX packets:68 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4496 (4.3 KiB) TX bytes:4496 (4.3 KiB)

sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

pppoeconf configja??? /etc -ben csak ppp-re vonatkozo dolgokat találtam,hol keressem

interfaces:

# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

iface dsl-provider inet ppp
provider dsl-provider

# please do not modify the following line
pre-up /sbin/ifconfig eth1 up # line maintained by pppoeconf

alap nem szerkesztgettem

modulok pppoeconf elõtt:
fglrx 273152 7
ipv6 279584 8
evdev 10368 0
btaudio 19348 0
forcedeth 19776 0
nvnet 75752 0
nvsound 1713132 0
eth1394 22800 0
sata_nv 10052 0
libata 51400 1 sata_nv
ohci1394 36420 0
sr_mod 18148 0
sbp2 27656 0
ieee1394 120920 3 eth1394,ohci1394,sbp2

után:
pppoe 16256 0
pppox 4624 1 pppoe
ppp_generic 29408 2 pppoe,pppox
slhc 8064 1 ppp_generic
fglrx 273152 7
ipv6 279584 8
evdev 10368 0
btaudio 19348 0
forcedeth 19776 0
nvnet 75752 0
nvsound 1713132 0
eth1394 22800 0
sata_nv 10052 0
libata 51400 1 sata_nv
ohci1394 36420 0
sr_mod 18148 0
sbp2 27656 0
ieee1394 120920 3 eth1394,ohci1394,sbp2

igen próbálatam azt is de semmi

pppoe -I eth1 aumúgy annyit ír :
„timeout waiting for PADO packet” vagy valami ilyesmi

nvidia „release notes” ja szerint:

…
For distributions based on a 2.6 series kernel, the module configuration file is typically called /etc/modprobe.conf. Some distributions use a subdirectory, /etc/modprobe.d/ , to hold individual configuration files for sound modules, etc.
…
If your configuration file already contains an entry for the forcedeth driver (an open-source network driver that supports the nForce network controller), that entry needs to be commented out with a # or removed:

# alias eth0 forcedeth

Add the following line to the configuration file:

alias eth0 nvnet

If your system has multiple ethernet interfaces, you may need to use ‘eth1’ or higher in place of ‘eth0’.

szóval forcedeth modulba van fordítva de azzal sem tudtam beizzítani…

de a legjobb:
There is currently no troubleshooting information for the nvnet network driver.

kösz az nvidia-nak 😀

amugy probáltam „woody” -san /etc/modutils/aliases szerkesztés majd update-modules

valamint /etc/modprobe.d/aliases -hez is hozzáadni alias eth1 nvnet de semmi
tipp?