Kezdőlap › Fórumok › Ubuntu Linux › Ndiswrapper
- This topic has 13 hozzászólás, 5 résztvevő, and was last updated 18 years, 11 months telt el by admin.
- SzerzőBejegyzés
- 2005-06-10-07:08 #2019723
Szia!
A modprobe után nem ír ki hibát? Akkor a modult betölti.
Utána van még egy kapcsoló (talán -m), amivel be tudod állítani, hogy a modult mindig betöltse. Ha a modul be van töltve, akkor az iwconfig paranccsal tudod a kártya paramétereit állítani (IP-cím, SSID stb.). Nekem Mandriva alatt a Control Centerben is lehet grafikusan állítani, biztos nálad is van ilyen lehetõség.
Ha kell még valami este megnézem otthon, nekem is RTL8180-as kártyám van Ndiswrapperrel.2005-06-11-07:13 #2019724Code:morzel@ubuntu:~$ su
Password:
root@ubuntu:/home/morzel # ndiswrapper -l
Installed ndis drivers:
net8180 driver present
root@ubuntu:/home/morzel # modprobe ndiswrapper
root@ubuntu:/home/morzel # ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:3336 errors:0 dropped:0 overruns:0 frame:0
TX packets:3336 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:303486 (296.3 KiB) TX bytes:303486 (296.3 KiB)root@ubuntu:/home/morzel # iwconfig
lo no wireless extensions.eth0 no wireless extensions.
sit0 no wireless extensions.
sit0 no wireless extensions.Eddig erre jutottam. Tudja valaki, hogy mit rontottam el?
2005-06-11-07:35 #2019725sztem nezd meg hogy sikeres volt-e a modul betoltese? dmesg?
2005-06-11-07:41 #2019726Szia!
Próbálj meg kiadni egy ifconfig wlan0 up parancsot, hátha csak el kell indítani a kártyát.
Imi2005-06-11-07:56 #2019727sztem nezd meg hogy sikeres volt-e a modul betoltese? dmesg?
[align=right][snapback]137944[/snapback][/align]Haat….
Az az igassag, hogy a ledek sem egnek a pcmcia kartyan, de dmesg:Code:root@ubuntu:/home/morzel # modprobe ndiswrapper
root@ubuntu:/home/morzel # dmesg
Linux version 2.6.10-5-386 (buildd@terranova) (gcc version 3.3.5 (Debian 1:3.3.5-8ubuntu2)) #1 Tue Apr 5 12:12:40 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 – 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 – 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 – 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 – 000000001f7d0000 (usable)
BIOS-e820: 000000001f7d0000 – 000000001f7efc00 (reserved)
BIOS-e820: 000000001f7efc00 – 000000001f7fb000 (ACPI NVS)
BIOS-e820: 000000001f7fb000 – 000000001f800000 (reserved)
BIOS-e820: 00000000e0000000 – 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 – 00000000fec02000 (reserved)
BIOS-e820: 00000000fed20000 – 00000000fed9b000 (reserved)
BIOS-e820: 00000000feda0000 – 00000000fedc0000 (reserved)
BIOS-e820: 00000000ffb00000 – 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 – 0000000100000000 (reserved)
503MB LOWMEM available.
On node 0 totalpages: 128976
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 124880 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 HP ) @ 0x000fe270
ACPI: RSDT (v001 HP 099C 0x25020520 HP 0x00000001) @ 0x1f7efc84
ACPI: FADT (v002 HP 099C 0x00000002 HP 0x00000001) @ 0x1f7efc00
ACPI: MADT (v001 HP 099C 0x00000001 HP 0x00000001) @ 0x1f7efcb4
ACPI: MCFG (v001 HP 099C 0x00000001 HP 0x00000001) @ 0x1f7efd10
ACPI: DSDT (v001 HP DAU00 0x00010000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfec01000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/hda6 ro quiet splash
mapped APIC to ffffd000 (fec01000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1296.911 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80×25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 503964k/515904k available (1436k kernel code, 11360k reserved, 754k data, 224k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode… Ok.
Calibrating delay loop… 2555.90 BogoMIPS (lpj=1277952)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: afe9fbbf 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: afe9fbbf 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: afe9fbbf 00000000 00000000 00000040 00000000 00000000
CPU: Intel(R) Celeron(R) M processor 1.30GHz stepping 06
Enabling fast FPU save and restore… done.
Enabling unmasked SIMD FPU exception support… done.
Checking ‘hlt’ instruction… OK.
Checking for popad bug… OK.
ACPI: Looking for DSDT in initrd… not found!
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking if image is initramfs…it isn’t (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 4248k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xf0322, last bus=3
PCI: Using MMCONFIG
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [C002] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge – 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [_SB_.C002._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.C002.C067._PRT]
ACPI: Embedded Controller [C004] (gpe 16)
ACPI: Power Resource [C1BD] (on)
ACPI: PCI Interrupt Link [C0D7] (IRQs 10 *11)
ACPI: PCI Interrupt Link [C0D8] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0D9] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0DA] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0ED] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C0EE] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [C0EF] (IRQs *10 11)
ACPI: PCI Interrupt Link [C0F0] (IRQs 10 11) *0, disabled.
ACPI: Power Resource [C250] (off)
ACPI: Power Resource [C251] (off)
ACPI: Power Resource [C252] (off)
ACPI: Power Resource [C253] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the “pci=routeirq” argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of “lspci” to [email protected]
** so I can fix the driver.
pnp: 00:09: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:09: ioport range 0x1000-0x107f could not be reserved
pnp: 00:09: ioport range 0x1100-0x113f has been reserved
pnp: 00:09: ioport range 0x1200-0x121f has been reserved
audit: initializing netlink socket (disabled)
audit(1118483071.575:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch ([email protected])
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards…
isapnp: No Plug & Play device found
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ACPI: PCI interrupt 0000:00:1e.3[B] -> GSI 22 (level, low) -> IRQ 22
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 2
Cannot allocate resource for EISA slot 7
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
Restarting tasks…<6> Strange, kswapd0 not stopped
Strange, kseriod not stopped
done
ACPI wakeup devices:
C067 C0BA C0C1 C0C2 C0C3 C0C4
ACPI: (supports S0 S3 S4 S4bios S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4248KiB [1 disk] into ram disk… done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 224k freed
ACPI: Fan [C254] (off)
ACPI: Fan [C255] (off)
ACPI: Fan [C256] (off)
ACPI: Fan [C257] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [C000] (supports 8 throttling states)
ACPI: Thermal Zone [TZ1] (47 C)
ACPI: Thermal Zone [TZ2] (39 C)
ACPI: Thermal Zone [TZ3] (27 C)
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 16
ICH6: chipset revision 3
ICH6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2580-0x2587, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0…
hda: ST94011A, ATA DISK drive
hdb: SONY CD-RW/DVD-ROM CRX835E, ATAPI CD/DVD-ROM drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 >
Probing IDE interface ide1…
Probing IDE interface ide2…
Probing IDE interface ide3…
Probing IDE interface ide4…
Probing IDE interface ide5…
Stopping tasks: ==|
Freeing memory… done (455 pages freed)
Restarting tasks… done
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
Adding 264560k swap on /dev/hda5. Priority:-1 extents:1
EXT3 FS on hda6, internal journal
hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
lp: driver loaded but no devices found
mice: PS/2 mouse device common for all mice
Synaptics Touchpad, model: 1
Firmware: 6.2
Sensor: 37
new absolute packet format
Touchpad has extended capability bits
-> multifinger detection
-> palm detection
-> pass-through port
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
serio: Synaptics pass-through port at isa0060/serio4/input0
ts: Compaq touchscreen protocol output
ieee1394: Initialized config rom entry `ip1394′
SCSI subsystem initialized
sbp2: $Rev: 1219 $ Ben Collins
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: [email protected]
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
cdrom: open failed.
input: PC Speaker
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 915GM Chipset.
agpgart: Maximum main memory to use for agp memory: 431M
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xc0000000
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 23, io base 0x2000
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
uhci_hcd 0000:00:1d.1: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 17, io base 0x2020
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 18, io base 0x2040
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.3: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: irq 19, io base 0x2060
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: Intel Corp. 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 23, pci mem 0xd0580000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
hw_random: RNG not detected
ACPI: PCI interrupt 0000:00:1e.2[A] -> GSI 21 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1e.2 to 64
intel8x0_measure_ac97_clock: measured 49478 usecs
intel8x0: clocking to 48000
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI interrupt 0000:02:06.0[A] -> GSI 18 (level, low) -> IRQ 18
Yenta: CardBus bridge found at 0000:02:06.0 [103c:099c]
Yenta: ISA IRQ mask 0x0cf8, PCI irq 18
Socket status: 30000820
ohci1394: $Rev: 1223 $ Ben Collins
ACPI: PCI interrupt 0000:02:06.2[C] -> GSI 22 (level, low) -> IRQ 22
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[22] MMIO=[d0001000-d00017ff] Max Packet=[2048]
b44.c:v0.95 (Aug 3, 2004)
ACPI: PCI interrupt 0000:02:0e.0[A] -> GSI 16 (level, low) -> IRQ 16
eth0: Broadcom 4400 10/100BaseT Ethernet 00:12:79:c4:50:7a
ieee1394: Host added: ID:BUS[0-00:1023] GUID[718b500029c91ea6]
ACPI: AC Adapter [C16B] (off-line)
ACPI: Battery Slot [C16D] (battery present)
ACPI: Battery Slot [C16C] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [C1E0]
ACPI: Lid Switch [C1E1]
ibm_acpi: ec object not found
ACPI: Video Device [C054] (multi-head: yes rom: no post: no)
apm: BIOS not found.
[drm] Initialized drm 1.0.0 20040925
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized i915 1.2.0 20040405 on minor 0: Intel Corp. Mobile Graphics Controller
mtrr: base(0xc0020000) is not aligned on a size(0x300000) boundary
cs: IO port probe 0x0100-0x04ff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: excluding 0xcf8-0xcff
cs: IO port probe 0x0a00-0x0aff: clean.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02f0500(lo)
IPv6 over IPv4 tunneling driver
ndiswrapper version 1.1 loaded (preempt=yes,smp=no)
root@ubuntu:/home/morzel #2005-06-11-08:04 #2019728Szia!
Próbálj meg kiadni egy ifconfig wlan0 up parancsot, hátha csak el kell indítani a kártyát.
Imi
[align=right][snapback]137946[/snapback][/align]Code:root@ubuntu:/home/morzel # ifconfig wlan0 up
wlan0: ERROR while getting interface flags: No such device2005-06-11-08:47 #2019729szia
nem egnek a ledek? hat az nem nagyon joo… nekem akkor is egtek amikor meg nem tudtam elinditani a kartyamat linux alatt…
amugy ha ndiswrapper -l -t nyomsz akkor ki kene irnia hogy
driver present, device present…m$ alatt nem probaltad a kartyat? biztos hogy muxik??
2005-06-11-09:17 #2019730szia
nem egnek a ledek? hat az nem nagyon joo… nekem akkor is egtek amikor meg nem tudtam elinditani a kartyamat linux alatt…
amugy ha ndiswrapper -l -t nyomsz akkor ki kene irnia hogy
driver present, device present…m$ alatt nem probaltad a kartyat? biztos hogy muxik??
[align=right][snapback]137960[/snapback][/align]ms alatt mukszik. mondjuk linux alatt csak annyit ir ki, hogy driver present. device present nincsen 🙁
Kozerdeku kozlemeny: Keresek valakit, aki be tudna nekem izzitani linux ala egy dwl-610 pcmcia kartyat debrecenben vagy kornyeken. termeszetesen a faradozasat megfizetnem, csak vegre mukodjon. [email protected]
:unhappy: :'(
Morzel
2005-06-11-09:41 #2019731ki kell irnia hogy device present ami azt jelenti hogy erzekeli a kartyat.
viszont nem ertem miert nem egnek a LEDek?
mas PCMCIA kartya muxik a gepeden?
sztem a hotplug rendszerrel lehet vmi baj…2005-06-11-10:16 #2019732ki kell irnia hogy device present ami azt jelenti hogy erzekeli a kartyat.
viszont nem ertem miert nem egnek a LEDek?
mas PCMCIA kartya muxik a gepeden?
sztem a hotplug rendszerrel lehet vmi baj…
[align=right][snapback]137965[/snapback][/align]sajna nem irja ki, hogy device present. mas kartya meg momentan nincs nalam. a ledek sem egnek
- SzerzőBejegyzés
- Be kell jelentkezni a hozzászóláshoz.
legutóbbi hsz